Orange CR120HSolid-State Amplifier Product code: CR120H 120W Guitar Amplifier Head with Digital Reverbs, and Effects Loop. Orange Amplifiers expands its line of solid-state Crush amps with the new CR120H 120-watt Head. This Crush amp delivers more authentic Orange tone than ever, with both amp channels being designed after the Rockerverb. The clean channel sports two gain stages that start to break up when it's cranked, and the dirty channel uses four gain stages to deliver classic Orange overdrive tones.In stock for online shop 3 pcs
Orange CR120H Crush Pro BlackSolid-State Amplifier Product code: CR120H-BLK Crush Pix Pro series guitar amp is a transistor amp with 120 W output with possibility to connect speakers with 16Ohm impedance. It is two-channel amplifier with a classic switch between channels Clean and Dirty. Each channel has its own volume control and equalizer. Clean channel has 2-band equalizer, after switching on Dirty available is a three-band EQ and Gain controler. End section of amplifier consists of Master Volume and digital Reverb. Dimensions: 22.5 x 55 x 25 cm. Weight: 14.4 kg.In stock for online shop 2 pcs
Evolution Amps Amber 40 Amp
Evolution Amps Amber 40 Amp:Two-channel 40W guitar head built using VASA (Valve Architecture Semiconductor Amp) which features non-linearity, compression and typical for tubes distorted sound. The architecture of transformer power amplifier also allowed to achieve constant output power for 4, 8 and 16 ohm speakers. Head features a CLEAN/CRUNCH type channel and OVERDRIVE type channel. The whole amplifier is complemented with the high-quality digital reverb, enabled FX loop, four push-buttons footswitch and MIDI input and output. Connectible through: MIDI IN and MIDI THRU/OUT, Speaker outputs: 4 ohm (or 2 x 8 ohm), 8 ohm (or 2 x 16ohm), 16 ohm and a footswitch input for EFS-1 footswitch. Footswitch with 5 m cable is included. Dimensions: 450 x 176 x 200 mm. Weight: 7.0 kg. More information
Two-channel guitar head built using VASA (Valve Architecture Semiconductor Amp). The analysis of classic tube amp work made it possible to create an amplifier which features non-linearity, compression and typical for tubes distorted sound. A distinctive feature of AMBER is the overdriven sound of power amp section and the output power/volume control system. Thereby the volume change for overdriven tones is made by true change of the output power which guarantees fixed timbre within full volume range. The architecture of transformer power amplifier also allowed to achieve constant output power for 4, 8 and 16 ohm speakers.
AMBER features a CLEAN/CRUNCH type channel and OVERDRIVE type channel. Each of these channels has its own passive EQ section and is able to work in one of six modes with different compression and gain. The possibility of saving channel modes extends the range of available sounds while playing. Power LEVEL function (which can also be saved) makes it possible for the user to control the volume while playing.
The whole amplifier is complemented with the high-quality digital reverb, enabled FX loop, four push-buttons footswitch and MIDI input and output. The selected footswitch mode allows to adjust the functionality of the amplifier to the preferences of the player. There are six modes: from the simplest, as in typical two-channel amps, to the modes using banks and presets. The MIDI input allows to control the amplifier by the MIDI controller, while the MIDI output allows to control the MIDI effect by the amp.
CLEAN/CRUNCH WITH VALVE TYPE COMPRESSION
CLEAN/CRUNCH channel includes GAIN control, MODE indicator and switch, BASS and TREBLE controls. When channel is active, the OUTPUT POWER LEVEL indicator shows current power/volume level of the channel.
The channel has the following MODEs indicated by colour. Each MODE is specified by three parameters: BOOST – extra gain, CONTOUR – cut mid frequencies and COMPRESSION (valve type nonlinearity). Valve type compression-nonlinearity add more sustain for CLEAN sounds and make specific CRUNCH sounds. The higher settings of GAIN control and channel MODE with more BOOST makes sounds more crunched due to power amp clipping. Channel MODEs and OUTPUT POWER LEVELs can be STORE for each channel or preset. It allows you to have more CLEAN /CRUNCH sounds with required volume while playing.
OVERDRIVE CHANNEL WITH OUTPUT POWER AMP OVERDRIVE.
The channel includes GAIN control, , MODE indicator and switch, BASS, MIDDLE and TREBLE controls. When the channel is active, the OUTPUT POWER LEVEL indicator shows current power/volume level.
The channel has the following MODEs indicated by colour. Each MODE is specified by two parameters: BOOST – extra gain and COMPRESSION (valve type nonlinearity).
Due to true output power control future the overdriven sound is generated at the output power amp stage. Either GAIN control and BOOST of the channel MODE define overdrive saturation. OUTPUT POWER LEVEL and MASTER control define loudness of overdriven sound.
The master section includes FX LOOP, REVERB effect and OUTPUT POWER LEVEL switch and MASTER control. AMBER features an enabled (by footswitch button or as a preset parameter) serial FX LOOP with signal level switch. REVERB control sets loudness of the room reflection added to the dry signal.
The volume and true output power of AMBER is defined by OUTPUT POWER LEVEL indicator and MASTER OUTPUT POWER control (see the table). The OUTPUT POWER LEVEL is stored for each channel and preset. OUTPUT POWER LEVEL
allows to differentiate the volume of each channel or preset. The MASTER knob sets the overall volume of the amp. Change of the loudness by either OUTPUT POWER LEVEL and MASTER control does not affect the sound of the amp.
AMBER 40 HEAD:
Guitar input impedance: 1Mohm
FX Loop: serial, switchable signal level -10dBu or +4dBV
SEND output impedance: 400ohm
RETURN input impedance: 100kohm
Footswitch input for EFS-1 footswitch
MIDI IN and MIDI THRU/OUT
Speaker outputs: 4ohm (or 2 x 8ohm), 8ohm (or 2 x 16ohm), 16 ohm
Output power: 40Wrms, recommended minimum speaker(s) power 70W
Mains input: 100-240Vac, 50/60Hz, 2.2A
Dimensions (W x D x H): 450 x 176 x 200 mm
Weight: 7.0 kg
Cable length: 5 m
Connector: Jack stereo
Controls: four push buttons and four red LED indicators with six modes of operation
Dimensions (W x D x H): 300 x 76 x 40mm
Weight: 0.85 kg
Product rating:Evolution Amps Amber 40 Amp
Do you own Evolution Amps Amber 40 Amp, or have you had a chance to try it?
Write a review and share your opinion with others
- Your price incl. VAT 20%
- 465.59 £
- Normal price
- 593 £
or while stock lasts
- Shipping for FREE
Available also as an exhibition, or unpacked item, without any damage